Quick answer: Well pump replacement cost usually runs about $1,000 to $2,500 installed for a submersible pump, according to both Angi (2026) and HomeGuide (2025). Jet pumps cost less, roughly $400 to $2,200 depending on shallow or deep-well design, and constant pressure systems run about $1,300 to $5,000. Angi’s national average is $1,897. Depth, extra parts and emergency calls push the total higher, and prices vary by region.
The taps sputter, the pressure gauge sits near zero, and the contractor’s first words are “the pump is shot.” Before you approve a quote, it helps to know what a fair price looks like. By the end of this guide you will know the typical range for your pump type, which line items move the total, and when a repair makes more sense than a new pump.
What a new well pump costs, by pump type
National cost guides measure slightly different things, so their ranges do not match exactly. Each figure below is labeled with its source and year. All include installation unless noted.
| Pump type | Typical installed cost | Source and year |
|---|---|---|
| Submersible | $1,000 to $2,500 | HomeGuide, 2025 |
| Submersible | $1,000 to $2,500+ | Angi, 2026 |
| Shallow-well jet (wells up to 25 feet) | $400 to $1,000 | HomeGuide, 2025 |
| Shallow-well jet | $450 to $1,500 | Angi, 2026 |
| Deep-well jet (wells 50 to 100 feet) | $500 to $1,400 | HomeGuide, 2025 |
| Deep-well jet | $800 to $2,200+ | Angi, 2026 |
| Constant pressure (variable-speed drive) | $2,000 to $5,000 | HomeGuide, 2025 |
| Constant pressure | $1,300 to $4,000+ | Angi, 2026 |
| Typical replacement, all types | $974 to $2,821 (average $1,897) | Angi, 2026 |
| Typical replacement, all types | $900 to $2,500 | This Old House, 2026 |
The pump itself is often the smaller part of the bill. This Old House (2026) puts the pump unit alone at about $200 to $500 before installation. Not sure which type you have or need? See jet pump vs submersible pump. For variable-speed systems, see our guide to the constant pressure well pump.
Prices vary by region. Labor rates, travel distance and local well depths all change the total. HomeAdvisor’s 2026 data on pump repairs shows the spread: an average of about $1,210 in Denver, $630 in Houston and $400 in Miami.
How depth changes well pump replacement cost
Deeper wells need stronger pumps, more wire and more pipe, and more labor to pull and reset everything. Angi’s 2026 figures show how fast the range climbs:
| Well depth | Typical replacement cost | Source and year |
|---|---|---|
| Under 25 feet | $400 to $3,000+ | Angi, 2026 |
| 25 to 150 feet | $1,200 to $5,500+ | Angi, 2026 |
| Over 150 feet | $2,000 to $10,000+ | Angi, 2026 |
If you do not know how deep your well is, look for the well log or your state’s well records. Our guide on how deep a well is explains where to find them.
The 6 things that drive the price up
- Depth. Every extra foot adds wire, drop pipe and time spent pulling and lowering the pump.
- Horsepower. A deeper well or a bigger household needs a larger motor, and bigger pumps and motors cost more. Angi notes simply that “deeper wells need stronger equipment.”
- Pulling the pump. A submersible pump hangs on the drop pipe and wire, sometimes hundreds of feet down. This Old House notes some pumps weigh more than 100 pounds, and crews may use special lifting equipment. HomeGuide (2025) lists two-person crew rates of about $150 to $300 per hour.
- Wire and drop pipe. Old wire, corroded splices or cracked pipe are often replaced while the pump is out. Angi (2026) says new wiring or electrical repairs add to the total, at about $50 to $100 per hour.
- Pressure tank or switch at the same time. A worn tank or burned switch can wreck a new pump early, so contractors often replace them together (see the table below).
- Emergency calls. HomeAdvisor (2026) says weekend and after-hours rates are usually double, and most companies charge a minimum house call fee of about $100 to $150.
Cost table: parts that are often replaced with the pump
These figures include labor unless noted. They are useful for checking an itemized quote.
| Part or service | Typical cost | Source and year |
|---|---|---|
| Pressure switch | $120 to $175 | HomeAdvisor, 2026 |
| Pressure switch | $150 to $200 | HomeGuide repair guide, 2025 |
| Control box (3-wire pumps) | $200 to $500 | HomeAdvisor, 2026 |
| Control box | $300 to $600 | HomeGuide repair guide, 2025 |
| Motor start capacitor | $100 to $150 | HomeAdvisor, 2026 |
| Check valve | $150 to $200 | HomeGuide repair guide, 2025 |
| Foot valve (jet pumps) | $150 to $300 | HomeAdvisor, 2026 |
| Pitless adapter | $150 to $450 | HomeAdvisor, 2026 |
| Pressure tank | $500 to $1,000 | HomeGuide, 2025 |
| Pressure tank replacement | $800 to $1,500+ | HomeGuide repair guide, 2025 |
| Pump motor only | $500 to $1,000 | HomeGuide, 2025 |
| House call minimum | $100 to $150 | HomeAdvisor, 2026 |
If your system uses a combination pump and tank unit, Angi (2026) notes it is usually easier and cheaper to replace the whole system than one part.
Repair or replace? A quick decision guide
Many “dead pump” calls end with a much smaller bill. According to HomeGuide’s 2025 repair guide, most well pump repairs cost $300 to $600 (national average about $450). HomeAdvisor’s 2026 average repair is $974. A new pressure switch or capacitor costs a fraction of a new pump.
Lean toward repair when:
- The pump is fairly young and the fault is at the surface: a pressure switch, control box part, capacitor or tank.
- A pro’s tests show the motor and cable are healthy.
- The problem started suddenly after a clear event, such as a storm or a frozen line.
Lean toward replacement when:
- The pump is near the end of its life. HomeGuide puts typical lifespan at 8 to 15 years and suggests considering replacement past 10 to 15 years; HomeAdvisor says about 15 years.
- The motor or pump end has failed and the pump has to be pulled anyway.
- Output has faded for months, or sand has worn the impellers.
- The pump is the wrong size or type for the well.
Pro tip: Once a pump is out of the well, most of the labor is already spent. If an older pump has to be pulled for a pump-end repair, ask for a price on a new pump too, so you are not paying for a second pull a year later.
Signs your well pump is failing
HomeGuide and Angi list similar warning signs. Each one has other possible causes, so check the linked guide before assuming the pump is finished:
- No water or a pump that won’t start: often a breaker, switch or control box. See well pump not turning on.
- A pump that runs nonstop: a leak, stuck switch, low well or worn pump. See well pump won’t shut off.
- A breaker that keeps tripping: a failing motor, damaged wire or bad capacitor. See well pump keeps tripping breaker.
- Rapid on-off clicking: usually the pressure tank, not the pump. See well pump short cycling.
- Weak or falling pressure: see low water pressure from a well.
- Spitting faucets, air or sediment in the water: could be a worn pump or a falling water level. See signs your well is running dry.
- A higher electric bill or new noises from the pump or tank.
Mistake to avoid: Replacing a pump without fixing a waterlogged tank or a low well. The new pump inherits the same problem and can fail early.
Questions to ask a contractor before you sign
Get at least two written, itemized quotes if the situation is not an emergency.
- Are you licensed for pump work in this state? Requirements vary, so ask.
- What exactly failed, and how did you test it? Ask whether they checked voltage, amp draw and insulation resistance before calling it a pump failure.
- What pump type, horsepower and flow rate are you installing, and why? It should match your well’s depth and yield and your household’s use.
- Is the price for the pump alone, or pump, wire, drop pipe, check valves and fittings?
- Will you replace the pressure switch or tank, and are they actually worn?
- Does the price include disinfecting the well? The Connecticut Department of Public Health recommends disinfection any time the inside of the well is opened, including pump replacement, followed by a bacteria test once no chlorine remains. See how to shock a well.
- What warranty covers the pump, and who covers the labor to pull it?
- Are there after-hours or weekend charges?
- Will you give me the pump details in writing? Record the model, horsepower, pump setting depth and install date for next time.
Frequently asked questions
How much does it cost to replace a submersible well pump?
About $1,000 to $2,500 installed in a typical well, according to HomeGuide (2025) and Angi (2026). Deep wells can cost much more; Angi lists $2,000 to $10,000+ for wells over 150 feet.
How much does it cost to replace a well pump and pressure tank?
Add the two ranges. HomeGuide’s 2025 guides put a pressure tank at about $500 to $1,000, or $800 to $1,500+ as a replacement job, on top of the pump. Get an itemized quote.
How long does a well pump last?
HomeGuide estimates 8 to 15 years; HomeAdvisor says about 15. Short cycling, sand and a low water level can shorten that.
How long does it take to replace a well pump?
HomeGuide (2025) estimates 3 to 6 hours for a typical installation. Deep wells, stuck pipe or extra repairs take longer.
Related guides
- Jet pump vs submersible pump: which fits your well?
- Well pump not turning on: step-by-step troubleshooting
- Signs of a bad pressure tank
Sources
- Angi – How Much Does Well Pump Replacement Cost? (2026)
- HomeGuide – How Much Does a Well Pump Cost to Replace or Install?
- HomeAdvisor – How Much Does Well Pump Repair Cost?
- Connecticut Department of Public Health – Disinfection Procedure for Private Wells
Costs in this guide are national estimates from published cost guides; actual prices vary widely by region, well depth and contractor. Pump circuits carry dangerous voltage; turn off the breaker and hire a licensed pump installer for electrical work or work in the well.
Leave a Reply